turbocharged 270hp 2.3L I4 6-speed manual AWD
Mazda MazdaSpeed6 in Alabama, United States Nov 2009 - Jun 2012 | |||
Jan 2010 | Ticking Noise from purge valve, according to service ticket. Previously, in dealership 26 days for Cam ticking noise. Not sure what was really going on this time. Hired Lemon Lawyer. |
Mazda MazdaSpeed6 in Arizona, United States Oct 2009 - Sep 2013 | |||
Nov 200913000 mi | Passenger side power door lock does not function. |
Mazda MazdaSpeed6 in California, United States Oct 2009 - Jun 2022 | |||
Nov 200912000 miUS $160 | Purge valve replaced under warranty, all drivetrain oils and oil filter changed | ||
May 201015900 miUS $100 | Steering wheel clock spring clicking, on order. Engine knocking, dealer agrees is unusual but waiting for Mazda to give them advice on the problem and solution. | ||
Oct 201018200 mi | Clock spring replaced in wheel...new spring still makes noise but it's ignorable. Engine still knocking, still can't replicate at dealership. Mazda states that it's normal operation. | ||
Jan 201335500 miUS $1000 | Leaking transfer case had to be resealed, parts replaced. All appears to be fine now. Leaking transfer case had to be resealed, parts replaced. All appears to be fine now. | ||
Feb 201766000 miUS $350 | O-ring failed between power steering pump and reservoir. Replaced pump and reservoir (reservoir had become stained inside and it was hard to tell what the level was). |
Mazda MazdaSpeed6 in Kansas, United States Jun 2009 - Aug 2018 | |||
Sep 200924000 mi | Engine light came on due to sensor, related to fuel system becoming faulty. Replaced under warranty. | ||
Oct 200925000 mi | Could not get part for leaking front differential. Quoted 1 day but took 3. | ||
Jul 201390700 miUS $310 | Left side rear shock was leaking - they need to be replaced as a pair so both rear shocks were swapped out for new. | ||
Jun 2015117000 miUS $100 | Pulley bearing for compressor went (very) bad. Quote from garage was $2,600 (for complete replacement of compressor which they misdiagnosed as bad). Bearing was $23. Fixed it with an ex-mechanic friend. |
Mazda MazdaSpeed6 in Quebec, Canada Nov 2010 - Jun 2011 | |||
Dec 201042780 mi | Check engine came on. Barely able to drive home. Engine would not rev unless gas pedal almost to the floor.Unplugged positive terminal of battery,waited 1-2 minutes and reconnected. Check engine light gone and car back to normal. |
Mazda MazdaSpeed6 in Ontario, Canada Feb 2011 - Dec 2013 | |||
Mar 201146500 miC $350 | Check engine light on, found that it was a purge valve, ordered part and fixed it. Problem seems like it is fixed. | ||
Dec 201378740 miC $1800 | Timing chain, actuator, seals, gaskets. |
Mazda MazdaSpeed6 in Minnesota, United States Feb 2017 - Jun 2018 | |||
Apr 2017134000 mi | Resealed the transfer case The turbo smoked when ideling or under heavy boost and was replaced |
Mazda MazdaSpeed6 in Ontario, Canada - Jul 2007 | |||
Jul 200762 mi | Car arrived off freight vehicle with damaged grill. Dealer promptly ordered replacement at no charge. |
Mazda MazdaSpeed6 in Puerto Rico Sep 2013 - Jan 2014 | |||
Nov 201346900 miUS $1200 | Engine broke two connecting rods and pistons; block was cracked down the middle. |
Mazda MazdaSpeed6 in Michigan, United States Jan 2013 - May 2013 | |||
Feb 201365300 miUS $100 | Timing Chain replaced |
Mazda MazdaSpeed6 in West Virginia, United States Jun 2009 - Aug 2012 | |||
Jun 201125000 miUS $500 | Shocks were getting soft. Replaced with somewhat better than OEM Bilstein shocks. |
Mazda MazdaSpeed6 in Alberta, Canada Mar 2008 - Apr 2011 | |||
Jun 20087440 mi | Replaced rear differential axle seals | ||
Feb 200911160 mi | Repaired sensor for fuel system that was squeeling when engine was cold. | ||
Apr 201018600 mi | Brought in to fix creek from drivers seat and rattle from rear of car. Dealer attempted to fix but still hasn't fixed either problem despite multiple trips in regards to these problems | ||
Mar 201137820 mi | Brought to dealer because of vibration and clunk from rear diff. Dealer tried to tell me it was the tires, but after further inspection found it was the rear diff bushings. Tried to tell me it wasn't covered under warranty. | ||
Apr 201138440 mi | Dealer attempted to repair rear differential after agreeing to do it under warranty. Got the car back after they had it for two days and it still had the same symptoms. Dealer attempted to repair rear differential after agreeing to do it under warranty. Got the car back after they had it for two days and it still had the same symptoms. |
Mazda MazdaSpeed6 in Ontario, Canada Jun 2008 - Aug 2013 | |||
Aug 200837200 mi | The rear brakes would stick on after disengaging the parking brake. The mechanic lubed the sliders and that seems to have fixed the problem. | ||
Jan 201164480 mi | Light came on during normal commute. Took to local mechanic who stated the code was for the EGR valve. Cleared the code and drove with mechanic, where code reader could tell valve was cycling (no problem). Valve may have frozen. | ||
Jul 201168200 miC $107 | AC quit blowing cold air. Dealer could not find a leak, but recharged system. AC blows cold now. | ||
Jan 201282400 mi | Leakage at fitting under compressor. | ||
Aug 201388040 miC $175 | A/C Compressor leaking. Quote $800 for new compressor instaled. Had it re-charged instead. |
Mazda MazdaSpeed6 in California, United States May 2009 - Jun 2011 | |||
May 201038300 miUS $280 | Front left wheel bearing noise at 38k. Apparently a common failure on this model. | ||
Oct 201046000 miUS $100 | Left front lower control arm bushing has cracked and is making a creaking sound when loaded. Dealer diagnosed the issue, but no parts are available. Was told that it isn't a safety issue and that the car can be driven until parts are in. | ||
Nov 201046800 miUS $350 | Replaced front left lower control arm on second trip to dealer after parts were not available on first trip. In the meantime, the failure of said part completely destroyed my left front tire. Mazda denied any after warranty assistance. | ||
Dec 201048000 mi | Progressively worse rattle in valvetrain at startup. Diagnosed as failed variable valve timing (VVT) actuator. TSB found, replaced under drivetrain warranty | ||
Mar 201151000 mi | Second visit to diagnose a prominent clunk in the drivetrain. Shop "could not duplicate" during first visit in Dec. This time, I took a tech for a ride. He noticed it right away. They had the car for a week, but could not locate its origin. Failed bypass valve in the turbo plumbing. Second failed stock Mazda valve in 50k miles. Was told that Mazda would only cover a portion of the replacement cost, so I told them to forget it and bought a Forge bypass valve as a replacement. Diagnosed/fixed rear window creaking/popping problem in the Speed6. Detached fixing hardware from rear edge of headliner and used taped vise-grips to bend the rear window guide tabs downward toward the front of vehicle to mitigate creaking. |
Mazda MazdaSpeed6 in Quebec, Canada Jun 2009 - Oct 2009 | |||
Sep 200919840 mi | Turbo seals replaced to fix oil leak. |
Mazda MazdaSpeed6 in Delaware, United States Jun 2009 - Jun 2012 | |||
Aug 200920000 mi | Had DTC P2187 Lean condition at idle on Bank 1. Dealer replaced High Pressure Fuel Pump on engine. Pump runs off of camshaft operating between 485psi and 1885 psi. | ||
Sep 200921000 mi | Replaced purge valve. Trm levels incorrect. Existing purge valve sticking. | ||
Oct 201147000 mi | Replaced smoking turbocharger with new updated turbo. |
Mazda MazdaSpeed6 in Washington, United States Aug 2008 - Dec 2009 | |||
Jun 20087500 mi | car wouldn't run past idle (felt like flooding/starving for fuel) brought into dealership, replaced High Pressure Fuel pump (took almost 2 weeks in shop) | ||
Feb 200957000 mi | Brought car in with suspected broken rear axle, found left rear broken, was replaced under warranty) While there, dealer found metal shavings in front transfer case (replaced front left driveshaft under warranty as well, and replaced associated fluids) | ||
Apr 200960000 mi | bad grinding and clicking sounds coming from drivetrain. vibrations above 50mph, and car jerked to a stop when slowing at 1-2mph Transfer case replaced |
Engine not specified
Mazda Mazda6 in Ontario, Canada Nov 2009 - Mar 2010 | |||
Dec 200929760 mi | Heated seats stopped working - bringing it again next week in the shop - fourth time for the same problem. They even replaced the entire seat... still having electric gremlins... |
212-horsepower 3.0L V6 6-speed shiftable automatic FWD
Mazda Mazda6 in Illinois, United States Oct 2013 - Jun 2018 | |||
Oct 201377000 miUS $360 | A/C evaporator was leaking from corrosion, and heater core next to it was also corroded. Replacing both required removing the dashboard. Check engine light came on; caused by clogged evaporative leak detection pump. Pump was removed, tested, cleaned and reinstalled. | ||
Nov 201377700 mi | Check engine light came on again for a while, and then went off. Technician checked the OBD system and found no active codes. Immediately took the car to an emissions testing station, where it passed. | ||
May 201483000 miUS $250 | Air intake had dry rot and a tear, triggering the check engine light, and had to be replaced. | ||
Aug 201485900 miUS $150 | Needed new fan control module because cooling fan for A/C system was running at high speed whenever A/C was engaged. Second time this has happened, and it is common among 2003-2008 Mazda6s. | ||
Sep 201591000 mi | Engine fans were running on high speed all the time. Replaced fan control module (third time in last two years) under warranty. I've read that the fans draw more amps as they get older, damaging control module, but don't know if this is true. | ||
Dec 201592000 miUS $55 | Liftgate struts failed and could no longer hold liftgate up in open position. Easily replaced both struts in 5 minutes. | ||
Dec 201798000 miUS $500 | Water pump housing was leaking. Replaced pump and housing, pulley and drive belt. |
Mazda Mazda6 in Ontario, Canada Sep 2012 - Dec 2016 | |||
Apr 201256420 miC $50 | Patch flat tire | ||
Jul 20137812 miC $50 | Patch flat tire | ||
Aug 201379856 miC $1200 | Suspension control arm replaced Suspension control arm replaced, along with Brake pads/rotors and tune up (plugs, air filter) | ||
Mar 201492380 miC $600 | Both Front Wheel Bearings replaced | ||
Sep 2015112840 miC $300 | Flex pipe repair |
Mazda Mazda6 in Alberta, Canada Aug 2012 - Sep 2013 | |||
Jan 2013 | I feel a little sloppiness in the driver's front control arm/ ball joint. I will have to keep an eye on it. Front exhaust heat shield started to rattle. Fixed with screws. |
Mazda Mazda6 in British Columbia, Canada Oct 2008 - Jul 2015 | |||
Dec 20081240 mi | Engine would not start. Required 2 tow-ins to shop. Problem (appeared) to be a short circuit in wiring b4 fuses. Dealer hung onto car to ensure repair was effective. | ||
Aug 201344640 miC $125 | TIE ROD JOINT TOO TIGHT-NOISEY! MECH ADJUSTED, ALL IS GOOD | ||
Dec 201457040 miC $100 | No Heatn climate control- Dealer could find no fault. Owner reset car thru removing/reinstalling battery cables. Heater works now! |
212-horsepower 3.0L V6 6-speed shiftable automatic FWD
Mazda Mazda6 in Arkansas, United States Jun 2013 - Jun 2018 | |||
Aug 2014113100 miUS $800 | Water pump failed. Replaced hoses also while in. | ||
Mar 2015118000 miUS $700 | Fixed engine oil leak. | ||
Jul 2016126300 miUS $1400 | Replace control arms, new struts |
Mazda Mazda6 in North Carolina, United States May 2009 - Mar 2010 | |||
Jan 200922000 mi | Transmission delays before engaging taking off from stoplight. Computer update was done. No cost. |
212-horsepower 3.0L V6 5-speed manual FWD
Mazda Mazda6 in Pennsylvania, United States Nov 2010 - May 2014 | |||
Jan 2013109300 miUS $1333 | Clutch started to make noise and be very heavy. Replaced entire clutch assembly. Something went wrong with the pressure plate and the throw out bearing was ruined. Lining low but some life left. | ||
Sep 2013122000 miUS $762 | A small plastic part on the water pump housing started to leak coolant. The entire water pump had to be replaced because they do not sell the plastic part separately. | ||
Nov 2013126000 miUS $453 | Front bypass hose fitting burst, spraying coolant |
Mazda Mazda6 in New York, United States Jan 2013 - Dec 2017 | |||
Jan 2014120000 miUS $1250 | car refused to respond to throttle, stayed at idle. replace air intake tube throttle body | ||
Nov 2014136000 miUS $1300 | Clutch slipping at higher rpm, pressure plate clutch disc and throw out bearing replaced |
156-horsepower 2.3L I4 5-speed shiftable automatic FWD
Mazda Mazda6 in Oklahoma, United States Oct 2010 - Jan 2011 | |||
Dec 201045000 miUS $180 | Power steering pump started making noises a while back, but only when steering hard one way or another and went away as soon as you weren't 'locked' at the end. I replaced the pump and it went away. |
Mazda Mazda6 in New York, United States Aug 2009 - Dec 2017 | |||
Jun 201025000 mi | Damaged muffler seal was discovered after I noticed the car was louder than usual. | ||
Aug 2017116000 miUS $150 | Shift cable linkage |
Mazda Mazda6 in District of Columbia, United States Dec 2014 - Dec 2014 | |||
Dec 2014105000 miUS $750 | intake sensors shot, both replaced |
Mazda Mazda6 in Nova Scotia, Canada Jun 2014 - Apr 2015 | |||
Sep 201481840 miC $1000 | Rear brake pads and rotors needed replacement. Real calipers were seized and needed servicing. Front brakes needed general servicing. |
Mazda Mazda6 in Pennsylvania, United States Nov 2009 - Jul 2018 | |||
Mar 2016171000 miUS $450 | Thermostat replacement |
Mazda Mazda6 in Michigan, United States Jun 2008 - Mar 2009 | |||
Oct 200824000 miUS $35 | Passenger seat creaked when someone sat in it while driving. Had to replace seat frame assembly. |
Mazda Mazda6 in Minnesota, United States May 2016 - Mar 2018 | |||
Jun 2017119000 miUS $35 | Low beam headlight bulb burnt out, replaced both L and R bulbs. | ||
Jan 2018125000 miUS $65 | Front brake pads replaced |
Mazda Mazda6 in Michigan, United States May 2015 - May 2015 | |||
May 201584000 miUS $31 | New interior light housing for back seat |
Mazda Mazda6 in Utah, United States Sep 2016 - Jun 2017 | |||
Nov 2016109400 mi | Body control module was water damaged. Water entered car from windshield wiper bolt. Intermittent loss of control of interior lights, blinkers, windshield wipers, horn, and windows. | ||
Jun 2017195000 miUS $300 | Ac compressor full replacement |
Mazda Mazda6 in Hawaii, United States Jan 2011 - Jun 2018 | |||
Jan 2013102200 miUS $80 | Not sure why still veering right. New tires too | ||
Aug 201481400 miUS $100 | Rear automatic window could not roll up. Mechanic dis-assembled and re-assembled. Now works just fine. Door could not open from the inside. ABS pump not working Battery didn't last as long as it should have. Rear left window cannot roll down, not yet inspected. | ||
May 201592000 mi | Front left & right wheel bearings worn/ replaced. Motor mounts replaced | ||
Oct 201596000 mi | Abs pump broke | ||
Sep 2016107000 miUS $150 | System leak, A/C recharged, blowing warm air | ||
Jan 2018114000 miUS $700 | Motor mounts broken | ||
Apr 2018115100 miUS $256 | Motor mounts worn replaced 2x on 2 years. Better but still thugging on acceleration Thug noise still there when accelerating and releasing gas pedal. |
Mazda Mazda6 in Georgia, United States - Sep 2007 | |||
Sep 20073500 mi | Warranty Repair - Center Console cover defective & replaced |
Mazda Mazda6 in New Jersey, United States Nov 2015 - Apr 2018 | |||
Nov 2015118000 miUS $465 | Gear shift wouldn't engage properly so car didn't register it was in "Park" and wouldn't restart. |
156-horsepower 2.3L I4 5-speed manual FWD
Mazda Mazda6 in Ontario, Canada Oct 2012 - May 2016 | |||
May 2016127100 mi | Bearing noise from inside transmission. |
Mazda Mazda6 in Nova Scotia, Canada - Jan 2007 | |||
Jan 2007 | switch un plugged in center console for e brake light fixed under warantee |
156-horsepower 2.3L I4 5-speed shiftable automatic FWD
Mazda Mazda6 in Ontario, Canada Jan 2013 - Aug 2014 | |||
Mar 201358280 miC $780 | replaced both rear calipers and pads |
Mazda Mazda6 in Quebec, Canada Aug 2008 - Oct 2010 | |||
Jan 200913020 mi | Replacement of hatchback struts. Hatch would not stay opened properly, esp. when cold | ||
Dec 200924800 mi | Replaced 3 of 4 door mouldings that were discolored |
Mazda Mazda6 in Arizona, United States Oct 2011 - Oct 2011 | |||
Oct 2011US $200 | Wires leading to battery severely corroded twice during the time I owned the car |
Mazda Mazda6 in Quebec, Canada Nov 2012 - Jul 2013 | |||
Jul 201381840 mi | Rust, again, despite dealer "repair". |
Mazda Mazda6 in Illinois, United States Jun 2008 - Jul 2020 | |||
May 201013000 miUS $150 | Rear under car engine cover came loose, was hanging down, and became cracked after being driven. Dealer said it was due to hitting a parking curb or something, but I believe bolt fell out resulting in part becoming loose. No warranty. | ||
May 201123600 miUS $480 | Cannot recall exactly, but it was one of the engine sensors that had gone bad. Trip also included an oil change and fuel injector cleaning. | ||
Feb 201345600 miUS $450 | Oxygen sensor failed. Was replaced. | ||
Feb 201670600 miUS $400 | Replaced the rear motor mount |
156-horsepower 2.3L I4 5-speed manual FWD
Mazda Mazda6 in Ontario, Canada Sep 2016 - Jun 2022 | |||
Jun 202090520 miC $200 | Rear tie rod replaced | ||
May 202298580 miC $250 | Thermostat was in open position and not closing |
Mazda Mazda6 in California, United States Jun 2007 - May 2011 | |||
Apr 200713 miUS $16600 | |||
Jun 200926000 mi | Over last few mos,I began to notice chipping & cracking on the o/s rubber sash window mouldings(ALL 4!).The blk plastic trim it's attached to has corroded as well.Took to dlr,& they apprvd wrnty rpr. Waitin' 4 parts 2 come in. | ||
Jul 200926800 mi | Went in 07/28 to have side window sill trim rplcd. It seems they were wrng ones ordered,or parts supplier snt wrng ones.What-ev,things hppn.Re-sched appt for 08/04/09. Over last few mos,I began to notice chipping & cracking on the o/s rubber sash window mouldings(ALL 4!).The blk plastic trim it's attached to has corroded as well.Took to dlr,& they apprvd wrnty rpr.Waitin' 4 parts 2 come in. | ||
Aug 200927000 mi | Went back in 08/04. Correct parts ordered this time & successfully installed. Looks like new again. |
Mazda Mazda6 in Wisconsin, United States Jun 2013 - May 2016 | |||
Oct 201345700 miUS $85 | Alignment (car woudl drift to one side) | ||
Nov 201450200 miUS $40 | the struts that hold the hatch open wore out and I replaced them myself (only took 2 minutes) |